These pics come from a new aerospace test facility that they are constructing at the University of Notre Dame. The SSF-6 is working great.
I am attempting to make all of these fittings air tight as they are used for pressure measurements. We can¹t have any leaks. I had very little warpage of my base metal and I think this is really going to work out very well.
The University of Notre Dame
Institute for Flow Physics and Control (FLOWPAC)
The Hessert Laboratory for Aerospace Research
FEATURES OF SSQ6 SILVER SOLDER PASTE:
|Strength||Over 85,000 PSI||Over 70,000 PSI|
|Form||1 oz. tube||18 inch Rod|
|Flux||Mixed in||Flux coated|
|Melt Temp||1050° F||1150° F|
|Ease of Use||Very easy||Easy|
|Works on||Stainless, Brass, Steel, Copper, Bronze, Cast Iron||Stainless, Brass, Steel, Copper, Bronze, Cast Iron|
|Heat Source||Any torch||Any torch|
|Shelf Life||9 months||Years if Kept Dry in Tube|
|Clean Up||Water and wire brush||Water and wire brush|
|Position||All position||All position|
|Application||Apply cold then heat||Apply when metal is dull red|
Using SSQ6 Silver Solder Paste
For best results, clean your work area and make sure that everything's in order before you begin soldering. Next, clamp the silver parts that require soldering together into a vise. Make sure to position the ends so there are no gaps. Silver powdered solder can't fill in gaps but will flow around the joint to fuse the parts, so make sure that you get a good fit for optimum results.
Next, apply SSQ6 to the joint. The amount of solder used should only be equal to the thickness of the wire or sheet you're working on. Then, light the torch and position the flame so that both sides are heated equally.
In some instances where the melting point is too low for the torch temperature, solder can flow away from the joint before the parts you're working on can fuse. Thankfully, SSQ6 has a melting point of 1050º and has a tensile strength up to 85,000 PSI, which is almost 18 times the strength of regular solders.
For more information on SSQ6 and to watch instructional videos, click the links below:
We are solver brazing cupre nickel together using SSQ-6 silver solder from muggyweld.com. A propane torch was used on the two pieces of copper nickel, one tube was flared so the other could be inserted for tight fit.
Muggy Weld SSQ-6 is simple to use on brass, you just squeeze out the amount needed on the brass before you heat the part with your choice of torch.
We are using SSQ-6 to join two copper plates. Just push the plunger on the syringe and add the amount need for the solder joint. Copper has a variety of uses, it can be found in water piping in every building or home in North America. Copper is also used in A/C units, refrigeration, and is a good conductor of electricity.
A 1/8" steel plate is soldered to a copper end cap using Muggy Weld SSQ-6 56% silver solder paste.
Two pieces of brass are brazed with SSQ-6 and a propane torch.
This deep sea pole has a broken eyelet. We make the repair with SSQ-6 and a propane torch, as well as Cool Blue Heat Paste.
SSQ-6 is the perfect solution for jobs like this--parts are balancing, and if a rod were used they could easily be knocked over but the silver solder almost glues them together and acts like a jig when heated.
Using SSQ-6 silver solder paste, Mike silver solders a stainless steel plate to a piece of copper tubing.
A stainless steel threaded bolt is soldered to a brass nut using SSQ-6 silver solder paste in syringe form.
Copper has a variety of uses, and can be found in water piping in nearly every building or home in North America.
SSQ-6 silver solder paste is ideal for brass, copper, stainless steel, bronze, cast iron, copper nickel, chrome moly, steel, and german silver in any combination.
Muggy Weld SSQ-6 is simple to use on brass, simply squeeze the amount needed on the brass before you heat the part with your choice of torch.
Silver soldering a 1/8" steel plate to a copper end cap using Muggy Weld SSQ-6 56% silver solder paste.
Copper nickel or cupre nickel is a widely used alloy in the marine industry, due to its seawater corrosion resistance. It is typically composed of 95% copper and 5% nickel, 90/10 or 70/30 depending on the need.
Copper tubing is soldered to a brass plate using SSQ-6 Silver Solder Paste.
SSQ-6 is commonly used to silver braze brass to stainless steel, due to its ease of use and convenient syringe applicator.
There are many industrial, domestic, and small business uses for brazing copper to stainless steel. In this article, we will use the SSQ-6 silver solder paste to solder a stainless steel plate to copper tubing.